car key
文章来源: chinomango2015-12-11 15:54:13

1. 05 Lexus GS300

1.1 ignition key

VIN: JT8BD69S150204624  key 41403, 51113, 13513

https://www.remotesunlimited.com/specify.php?search=1&type=fcc&search_fcc=HYQ1512V 

http://www.keylessremotewarehouse.com/lexus_oem_lexus_fcc_id_hyq1512v_keyless_remote_entry_clicker_w_1_5_new_key_pre_owned_w_new_key_276aa_c_p538.htm

https://www.keylessentryremotefob.com/searchresults.asp?Search=Lexus&Search=2005&Search=GS300 

1.2. tire key

Overtigen will crack tire key. my GS300 2005 spec is:
85996, 00623 55501, PT276-30986, orange, Julian dat 16704

1.3. Ignition key programming

https://www.remotesremotes.com/2005-Lexus-GS-300-Keyless-Remote-Key-Fob-Clicker-s/4455.htm 

http://www.keymachine.com/images/ilco/SDDTOYLEX.pdf 
1. Close and lock all doors. Unlock and open drivers door.
2. Put key into ignition and remove. Do not turn it on.
3. Using the electric lock switch. Lock and unlock 5 times. (Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock, Unlock)
4. Close and open drivers door.
5. Using the electric lock switch. Lock and unlock 5 times. (Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock, Unlock)
6. Put key into ignition. Turn to "ON"  then "OFF" in one second, remove the key.
7. You will see the door locks cycle once. If not repeat 1-7
8. On the remote, press and hold the LOCK and the UNLOCK button at the same time for no more than 2 seconds.
9. On the remote, press the LOCK button for no more than 1 second.
AT THIS POINT, the locks should cycle by themselves ONE time. This means the procedure was accepted; IF the locks cycle twice it has failed.
The most common reason for programming failure is because the car didn’t receive a good signal from the remote. To fix this problem try these tips. 1) Stand outside of the car while you are performing steps 8 and 9. 2) Don’t hold the remote buttons down as long.
As long as the car is still in programming mode you can keep trying steps 8 and 9 until you complete the programming. If you wait too long and the car exits the programming mode then you must start over.
After you get the remote to program then continue on with step 10.
10. Close and open door to end programming procedure.

1. Insert an already programmed master key into the ignition. Do not turn.
2. Press and release the gas pedal 5 times.
3. Press and release the brake pedal 6 times.
4. Remove the key from the ignition.
5. Insert the new key you want to program into the ignition.
6. Press and release the gas pedal one time.
7. Wait 1 minute. The security light will be blinking for this one minute. When it stops blinking your key is programmed. To end programming step on brake one time.
NOTE: Look for your security light. This light will guide you during the programming procedure. The security light will go off at Step 1. It will remain off until Step 6. The security light will come on and start to blink after Step 6 until the key is programmed. If the security light comes on after Step 4 STOP the procedure and start over again.
If you perform this procedure too slowly your car will not go into programming mode. If you can not get your car to go into programming mode make sure you are using a master key and not a valet key. If you have a master key then you will probably need to perform this procedure more quickly.

 
You have to flash the ecu.There is no way around it.Toyota and Lexus have a one time deal where if this is your first time losing the keys they will waiver the cost of labor but still charge you for the keys.Not sure if they do that anymore.98-01gs300/400 has to be flashed. 02-05 gs300 are locksmith programable if they have the machine which i do.
Remote Programming
1. Open driver door, keep it open and in the unlocked position (all other doors should be closed)
2. Put original key in ignition and pull out
3. Lock and Unlock the doors 5 times (complete each lock/unlock cycle within 1 second and
entire process in 40 seconds or less)
4. Close the door and open the door
5. Lock and Unlock the doors another 5 times (complete each lock/unlock cycle within 1 second and
entire process in 40 seconds or less)
6. Put the key in the ignition, turn it to "on" and then off (with 1 second) and remove from the ignition.
7. Press and hold transmitter LOCK and UNLOCK buttons simultaneously for at least 1.5 seconds,
and then within 3 seconds; press any transmitter button for at least one second.
8. If within 3 seconds, door locks cycle one time, new transmitter code was accepted. If door locks
cycle 2 times, new transmitter code was not accepted. If code was not accepted retry step 8 again.
1.4. reset ECU and add new master key
Once the ECU is flashed, reinstall in the car. You need to have three keys programmed as a master: Insert your first master key, DO NOT TURN. Remove the key right away. Insert master key number 2, DO NOT TURN. Remove the key right away. Insert master key number 3, DO NOT TURN. Remove the key right away.
 
1.5.1 314.4MHz,4C chip
89070-53531
FCC ID:HYQ1512V https://fccid.io/HYQ1512V 
2002-2003 ES300 1998-2005 GS300
2001-2005 IS300 1998-2000 GS400
1998-2000 LS400 2001-2005 GS430
1.5.2 314.4MHz,4D-68 chip(B0-60)
FCC ID:HYQ1512V
2003 - 2008 LX470
2003 - 2009 GX470
1.5.3 314.4MHz ,4C chip
FCC ID:HYQ1512V
1998-2002 LX470
1.5.4 314MHz 89070-24171
FCC ID: HYQ12BBK canada 16511032233 Lexus 89070-24171 https://fccid.io/HYQ12BBK 
2003 2004 2005 2006 ES330
2002 2003 2004 2005 2006 SC430
2001 2002 2003 2004 2005 2006 LS430
1.5.5 312MHz, FCC ID:N14TMTX-1
1999 2000 2001 2002 USA RX300
1.5.6 314.4MHz
FCC ID: HYQ12BBT
2007 2008 2009 RX350
2004 2005 2006 RX330
2006 2007 2008 RX400h
1.5.7 60010/60140/48040
314.4MHz
USA Model
FCC ID:HYQ1512V 89785-50031?
1998-2002 LX470
2003 - 2008 LX470
2003 - 2009 GX470
1998-2002 Landcruiser
我新配钥匙不能启动,现已肯定是内芯问题。在发动时ECU与内芯通信失败。就钥匙是HYQ12BBK,内芯是50021 28F17。新壳是DENSO 12BBY-08, 里面只有一个10pin芯片。
 
2. 08 Odyssey
钥匙:编程: https://www.youtube.com/watch?v=X0VDkEF_ZJY Ebay上带芯片的光钥匙很便宜,螺丝和2x3x10的transponder要自己装上。
本地店Business websitesiliconvalleylockmasters.com1444 S Main St,Milpitas, CA 95035, (510) 790-2207 

2.1 编程

遥控器编程只能用于开关车门不能用于发动车。Transponder编程必须用编程器如Xhorse OBD、CK100+或Honda HDS。两者的编程步骤:https://www.youtube.com/watch?v=YMQlF4ztrFI#t=5m25s 首先是遥控器Fob编程:关好车门插入旧钥匙拧至ON,按遥控器键再OFF,如此重复3次,在第4次按键时车门会自动上锁再开,再按键仍如此。再按新遥控器键,关车即可。Transponder编程:CK100+接OBD口,插入旧钥匙拧至ON,CK100+选Immotolizer及车型,按屏幕提示操作add a key,钥匙OFF;再ON-OFF;插入新钥匙ON并在屏幕计数复0前OFF,重复ON-OFF;插入旧钥匙ON-OFF,再ON,显示已存储,按CK100+任意键结束。

大部分车的编程,Google店里可下装key programming procedure,启动后按左上角跳过广告。本地lockmaster是用CK100+的OBD,也就是提示步骤。
http://www.obd2eshop.com/reviews/pro104565? Email:sales@keyprom8.com Erin:+8618054815707
https://www.youtube.com/watch?v=xaR-u_EgO4I